Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Venice Homeowners
A missing or rusted-out cap is the fastest way for water, leaves, and nesting birds to get into a flue that was working fine last season. In Venice, where winter rain does most of its damage quietly between storms, a cracked crown or a cap that’s blown loose lets moisture soak into the masonry around the flue long before you notice a stain on the ceiling. Our technicians have up to 13 years of experience fitting caps and crowns built for the job, using professional-trade lines like Gelco and Olympia Chimney rather than whatever’s on the shelf at the hardware store. We answer 24/7 at (833) 725-4278, and same-day service is often available.
What Our Chimney Cap & Crown Service Includes
This is a dedicated preventive service for us, not an upsell tacked onto a sweep. Each job starts with a look at the whole chimney top so we know what the flue actually needs before anything is fitted.
Cap Installation
A chimney cap is the lid over your flue: a metal top on a mesh or louvered body that keeps rain, debris, and animals out while letting smoke escape. You need one if the flue is open to the sky, which is common on older Venice homes where the original cap rusted away or was never fitted. We measure the flue, select a cap sized to it, and secure it so wind off the flats doesn’t shift it.

Cap Replacement
Caps fail slowly. Rust eats through the mesh, a seam splits, or a storm bends the top out of shape, and suddenly the cap is letting in exactly what it was meant to block. Replacement makes sense when the existing cap is corroded, loose, or the wrong size for the flue. We remove the old unit, check the flue tile underneath for damage, and fit a new cap matched to the chimney.

Crown Repair
The crown is the concrete or masonry slab at the very top of the chimney, sloped to shed water away from the flue. When it cracks, water runs down into the chimney structure instead of off the sides, and that’s where expensive damage starts. We repair cracked and spalled crowns, rebuilding the slope so water moves away from the flue the way it should.

Crown Coating
Crown coating is a protective layer applied over a sound but weathered crown to seal hairline cracks and slow further deterioration. It’s the right call when the crown is intact but showing its age, and it’s far less costly than a rebuild. We clean and prep the surface first, because a coating only holds if what’s underneath is solid.
Multi-Flue Cap
A multi-flue cap covers two or more flues on the same chimney with one unit, which is common on larger Venice homes with a fireplace flue plus a furnace or water-heater flue alongside it. These need precise measuring so each flue still draws properly and the cap sits level. We build or specify the cap to the actual flue layout on your roof, not a one-size approximation.
Custom Cap
Some chimneys don’t take a standard cap: unusual flue shapes, oversize openings, or a look the homeowner wants to keep consistent with the house. A custom cap is fabricated to the exact dimensions of the flue and the crown. We take the measurements on site and work with trade suppliers like Copperfield and Famco to get a cap that fits the first time.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with an intentional set of professional-trade brands because cap and crown work lives or dies on material quality. Gelco caps and crowns are built for long service, and we know where their components wear and what to check when one has been up for years. Olympia Chimney products show up on a lot of the chimneys we see around Venice, and we’re familiar with how their caps and terminations are put together and where they typically need attention.
Famco and Copperfield round out the lines we carry and work with most often, covering everything from standard caps to custom fabrication. We use these brands because it’s what the trade uses, not what’s cheapest to source. Whether you have Gelco, Olympia Chimney, Famco, Copperfield, or any other make on your chimney, we can help.
Signs You Need Chimney Cap & Crown Right Now
- Water stains on the ceiling or chimney breast. A dark ring or peeling paint near the fireplace usually means water is getting past the crown or cap and soaking into the masonry. Left alone, that moisture works its way into the framing, and the repair grows from a cap job into a structural one.
- A cracked or crumbling crown. If you can see cracks in the concrete at the top of the chimney, or chunks flaking off, the slope is no longer shedding water. Crown repair now is a small job; a rebuilt crown plus masonry work later is not.
- Birds, squirrels, or debris in the flue. An open or damaged cap is an invitation. Nesting material blocks the flue and creates a fire hazard the first time you light a fire, so it’s worth closing the opening before the season starts.
- A rusted, loose, or missing cap. Rust through the mesh or a cap that shifts in the wind means it’s no longer doing its job. Replacement is straightforward and protects everything below it.
- Smoke backing into the room. A cap that’s the wrong size or a blocked flue can push smoke back into the house instead of up and out. It’s a sign worth having checked before you rely on the fireplace.
Our Chimney Cap & Crown Process – Step by Step
- 1
Roof-level assessment. We get up and look at the chimney top directly: cap condition, crown slope, flue tile, and flashing. Photos from the roof tell you more than any description, so we take them and show you what we see.
- 2
Written scope and flat price. Before any work is booked, you get the scope in writing with a flat price for the job. Nothing gets added without your agreement, and if part of what you were told you needed can safely wait, we’ll say so.
- 3
Material selection. We match the cap or crown material to your flue and your home, drawing on the professional-trade lines we work with. You’ll know what’s going on the chimney and why.
- 4
Installation or repair. Caps are fitted and secured; crowns are repaired or coated with the slope corrected so water sheds as it should. We work clean and check the fit before we come down.
- 5
Final check and photo report. We confirm the cap is seated, the crown drains properly, and the flue is clear, then leave you with photos of the finished work. If anything else needs attention, you’ll see the evidence for yourself.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Venice?
A typical cap installation in Venice runs $275 – $650 depending on flue size and cap style, while crown repair generally runs $350 – $900 depending on the extent of cracking and whether coating or a partial rebuild is needed. A full crown rebuild on a badly deteriorated chimney sits higher, often $900 – $1,800, and multi-flue or custom caps land somewhere between a standard cap and a fabrication job based on the measurements involved. These are typical estimates, and the written estimate sets the final price.
What moves the number: the number of flues, the size and shape of the opening, whether the crown needs coating versus rebuilding, and how much access the roof allows. To avoid overpaying, ask for the scope in writing and for photos of what’s actually wrong up there; nothing should be recommended without camera or roof-level evidence you can see. A free estimate from us includes the roof-level assessment, the written scope, and a flat price before anything is booked.
Chimney Cap & Crown Near Venice – Our Service Area
We work across Venice and the neighborhoods around it, including Marina del Rey, Mar Vista, Santa Monica, Culver City, Westchester, and Westwood. Homes closer to the water and the flats tend to see caps age faster, so we’re often out that way. If you’d like a look at our chimney cap & crown work nearby, or want the same service in chimney cap & crown for Mar Vista, we can book you into the next opening, Sunday through Friday.
Serving Venice, CA – Our Local Coverage Area
We serve Venice and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Venice
Chimney cap and crown work covers the two pieces at the top of your chimney that keep weather and animals out. The cap is the metal lid over the flue; the crown is the sloped masonry or concrete slab around it that sheds water. Together they protect everything below them, which is why we treat them as preventive work, not optional extras.
Most cap installations are done in a single visit, usually a couple of hours. Crown repair and coating take longer, often a full day once prep and curing are factored in, and a full rebuild can run into a second visit. We’ll tell you the expected timeline in the written estimate so you can plan around it.
Cap installation typically runs $275 – $650, crown repair $350 – $900, and a full crown rebuild $900 – $1,800 in Venice, with multi-flue and custom caps priced by measurement. The written estimate sets the final price, so the number you agree to is the number you pay. Call (833) 725-4278 for an exact quote; estimates are free.
Yes, we work with Gelco and Olympia Chimney caps and crowns, along with Famco and Copperfield, and we can service or replace caps from other makers too. We know where these components tend to wear and what to check on an older install. If your cap is a brand we don’t list, send us a photo and we’ll tell you what we can do.
Same-day service is often available, and we dispatch Sunday through Friday from 7am to 7pm. We answer 24/7, so a call outside dispatch hours is booked into the next opening. We’re closed Saturday.
We stand behind the work we do and will put the details in writing with your estimate. Rather than quote a blanket term here, we’ll spell out what’s covered for your specific cap or crown job. Ask when you book and it’ll be in your paperwork.
Clear access to the fireplace and the area around it, and let us know if there’s a gate code or a dog. You don’t need to do anything on the roof; that’s our job. If you have photos from a previous inspection, have them handy so we can compare.
Schedule Your Chimney Cap & Crown Service in Venice Today
If your cap is rusted, your crown is cracked, or you’re simply not sure what’s up there, a free estimate tells you where things stand. You’ll get the roof-level assessment, photos, and a flat price before any work is booked. Call (833) 725-4278. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Venice.